Replacing a Dead Kia Ceed Key Fob
Kia Ceed users love the convenience of remote entry. But, just like any other device, the key fob can not function for many reasons. The battery can be easily and affordably replaced.
The key fob has a 2032 lithium coin battery that is commonly referred to as CR2032 and found in many other electronic devices. A standard flathead screwdriver will be all that is needed to open the key fob and then replace the battery.
Keyless entry
The smart key fob of the KIA Ceed is an increasingly popular feature, making it easier to lock or unlock and even start the car. If yours doesn't work it could be because of an inactive battery or other issues. If the battery isn't operating correctly, it can impact the functions of the remote and the electronics within. To resolve this, check the retaining clips made of metal inside the fob to ensure they are in place and have completed the circuit. You may also need to clean the key fob with a cloth or isopropyl ethanol to make sure there aren't traces of water exposure.
The push buttons on the key fob in the front door handles transmit LF antenna signals to the vehicle. The vehicle's LF receivers in the door handles and in the trunk or tailgate read the challenge and transmit a response to the transponder. The information is then transferred to an interface for serial communication from the SMK ECU.
If you're experiencing problems with your Kia Ceed key fob, it's important to address the issue before it gets any worse. Fortunately, replacing kia ceed key TheKeyLab in a Kia key fob is easy and takes only about a couple of minutes. First, locate a small slot on the side of the key fob, typically just opposite the key hole. Simply insert a flathead screwdriver into the slot and then take off the plastic casing, without damaging the interior components.
Remote start
If your Kia Ceed key fob remote does not work properly, there are several options to try. Check the battery in the remote. If it's dead the remote won't work. Examine the battery connections again. If the connections are damaged, then it's likely that the battery will not be receiving the current. If the issue continues then you should try resetting the system. Disconnect the 12 Volt batteries for a few minutes to accomplish this. This will allow any residual electrical energy to be removed and the system to reset.
If the chip inside the key fob has been exposed to water, it could also stop working. It is recommended to make use of clean tapwater to wash the keyfob before letting it completely dry before replacing the battery. You can clean the key fob using isopropyl, or electronic cleaner. In some instances, the key fob can stop working after being dropped on the floor. This is due to damage to the internal microchip.
Additionally, the key fob can also stop working based on signal interference. This could be caused by weather conditions, objects in the near vicinity of the vehicle or transmitters that operate on the same frequency. In the majority of cases, it can be resolved by altering the key fob's programming. This can be accomplished by turning the key off to on in the ignition until the door locks are cycled.
Keyless lock
Key fobs are an excellent convenience for many drivers, however it's also a device that could break easily. The most common reason is a dead battery but it could also be a problem with the door locks. The good news is that an easy trip to the dealer is enough to fix the issue.
Smart key features on the Kia Ceed make life easier for you by allowing access to your vehicle without having to remove it from your pocket or purse. To unlock your car, simply place the key fob in close proximity to the vehicle, and press the lock button twice for the trunk and once for the driver door.
Both the traditional Kia key fob as well as the smart Kia make use of standard 2032 battery, which are sold in the majority of retailers or online stores. This kind of battery can also be used to power small electronic devices like calculators or watches. To replace the battery, you will need to find the small button that releases the mechanical blade of the key and take it off. Then, put the new battery in the slot that is exactly the size of the emergency key blade.
If you are experiencing problems with your key fob, ensure that all metal retaining clips are tightened and that there is no sign of water damage. You should also clean the contact points regularly. If these steps do not work, you might need go to an authorized dealer to reset the program.
Remote trunk release
You can remotely unlock and lock the Kia Ceed tailgate or trunk using the key fob. This feature is especially useful when you're away from your vehicle and need to ensure that the trunk is closed or open. To activate this feature, hold and press the button on your Smart Key FOB for at least a half-second. Press the button to turn off the feature. The key fob could also be used as an alarm to scare away potential thieves or aid in locating your vehicle in a huge parking lot.
A dead battery in the key fob is the main reason for a Kia to not function. You can replace the battery in just a few minutes. To do this, you will require a flathead screwdriver and a replacement key fob case. Find the small slot on the side. Inject the screwdriver into the slot and slowly push it until the case comes off. Replace the old battery with a new one.
Another reason that could cause the Kia key fob not working is water damage. It can happen when the key fob is wet. For instance dropping it in rain or spill water on it. If this happens, you should clean the electronic component using paper towels and isopropyl alcohol before reprogramming it. You could also try setting the on-board computer back to factory settings by disconnecting the 12 volt battery for a short period of time.